How to Use the Jacuzzi in Your Hotel Room

A tub with jets is easy to use once you know which kind you have. The usual problems, like jets that will not start, water spraying out or a tub full of foam, come down to a few things the owner's manual explains and the room rarely does. This guide sums up what the tub makers and the CDC say, for every kind of private tub you will find in a hotel room, a suite or a cabin.

TubHotels guide. . Based on tub and hot tub makers' manuals, the CDC and the CPSC.

Illustration: a two-person whirlpool tub on a tiled platform beside the bed in a hotel room
A whirlpool tub beside the bed. Illustration.

Which tub do you have?

The listing will not always tell you. Across the 5,445 room names on our lists, the tub is called a spa tub or spa bath in 27%, a jetted tub in 21%, a jacuzzi in 20%, a whirlpool in 19% and a hot tub in 8%, and a name can use more than one word. The words are used loosely, and the tub itself is the better guide. (Hot tub types explained goes through the names.)

TypeHow to spot itWhat it does
Whirlpool tub (jetted tub)Round nozzles on the sides that you can aim, and a covered suction fitting low on one wall.A pump pulls the bath water in and pushes it back out through the jets.
Air tub (air bath)Small holes in the floor of the tub, and no suction fitting.A blower sends warm air bubbles up through the water. It does not pump the water around.
Combination tubBoth of the above, usually with a separate button for each.Water jets and air bubbles, on their own or together.
Soaking tubNo jets and no holes.A deep bath. If the listing promised jets, tell the front desk.
Hot tub (spa)Usually stays filled and covered, with a control panel on the rim.Keeps its water heated and filtered between uses. It is private when it sits on your own balcony, deck or patio, or inside your suite.
Whirlpool tub and air tub comparedWhirlpool tubAir tub123
  1. Jets on the sides that you can aim (whirlpool)
  2. Suction cover, low on one wall (whirlpool)
  3. Small air holes in the floor, and no suction cover (air tub)
A whirlpool moves the bath water through jets; an air tub blows bubbles from small holes.

At most places on our lists the tub is indoors. Of the 5,900 hotels and rentals on our lists where a source confirms where it is, 59% have it in the bedroom, 38% in the bathroom and 2% on a private balcony or patio, and 1% have tub rooms in two places. Our data records where the tub is. Hotels rarely say whether it is a whirlpool, an air tub or both, so we cannot count each kind. Cabin listings rarely say where the hot tub is, so few of them are in these numbers. Our cabin pages list 790 cabins and lodges with a private hot tub, and the hot tub section below covers using one.

How to use a whirlpool tub

These steps come from the owner's manuals of Kohler, Jacuzzi, American Standard, MAAX, Aquatic and MTI. Your tub may differ a little, but the order is the same.

How full to fill a whirlpool tub1234
  1. About two thirds full: the most before you get in
  2. The water line
  3. At least 2 inches between the water line and the highest jet
  4. The highest jet
Fill above the jets before you press the button, and leave room for the water to rise when you get in.
  1. Check the suction cover

    Look for the cover over the suction fitting, the grille low on one wall. Every whirlpool manual we read says not to run the tub without it. If it is missing or cracked, call the front desk.

  2. Fill above the jets

    Close the drain and fill the tub with water at a comfortable temperature until it is at least 2 inches above the highest jet. Manuals ask for 1 to 2 inches, so 2 inches works for all of them. Some tubs have a sensor that keeps the pump off until the water is high enough.

  3. Leave room for yourself

    American Standard warns against filling more than about two thirds before you get in, since the water rises and can spill over the edge.

  4. Press the button once

    Most tubs have one round button on the rim: press once to start the jets, press again to stop them. Some hotel tubs have a panel instead, where you hold the power button for a few seconds to turn it off.

  5. Aim the jets and set the strength

    Swivel a nozzle to point it where you want. Twist the face of the jet to change the flow (brands turn opposite ways, so try both). A separate air knob makes the massage stronger or softer. Never close every jet.

  6. Keep it warm with the tap

    If your tub has an in-line heater, it only keeps warm water warm, and only while the jets run. It will not heat cold water. To warm the bath, add hot water from the tap.

  7. Restart when it stops

    Most tubs switch the jets off after about 20 minutes, some after 30, and some have no timer. Press the button again if you want more.

  8. Jets off, then get out

    Turn the jets off before you stand up: the water level drops below the jets and they spray. Get out slowly, then open the drain.

Illustration: the round on/off air button and air knob on the rim of a whirlpool tub
The round button starts and stops the jets; the knob beside it adds air. Illustration.
Illustration: a hand turning a chrome whirlpool jet under water
Swivel the nozzle to aim it, twist its face to change the flow. Illustration.

Air tubs and combination tubs

An air tub works the same way, with a few differences:

  • The button starts a blower. Press and hold it, or use the arrows, to change the bubble strength; some panels also have wave and pulse modes.
  • Fill above the jets first. One hotel guide says the air can go on any time, while Jacuzzi says not until the air holes are under water, so filling first is the safe choice.
  • The air can feel cool against warm water. MAAX says that is normal.
  • After your bath the blower may start again by itself for a minute or two. That is the drying cycle clearing water from the air lines.
  • A combination tub has a button for each system. Use either one or both together.

What you can put in the water

This is where the manuals carry the most warnings. The makers do not all agree, so here is what each says:

ProductWhat the makers say
Bubble bath, shampoo, body washJets make even a small amount foam heavily. Kohler and Villeroy & Boch say to avoid them while the jets run; MTI says to use them sparingly.
Dish soapMAAX says never: it foams so much it can clog the system.
Bath oilsEvery maker that mentions oils advises against them. They can damage the pump and the plastic parts.
Bath saltsThe makers disagree. American Standard says no, MAAX says use with caution, MTI and Villeroy & Boch say water soluble salts are fine.
Low-foaming powder or crystalsJacuzzi and Aquatic allow a small amount.
Bath bombs, Epsom salt, essential oilsNone of the manuals we read mentions them. MTI warns that dyes can stain the jets, so a colored bath bomb is a risk in a room you do not own.

In a rental, the host's rules come first. One cabin rental we read bans soaps, oils and bubbles outright.

Safety

The points the manuals and the CDC agree on.

Temperature
Keep the water at 104°F (40°C) or below, the limit the CDC, CPSC and the tub makers give. Check it with your hand or a thermometer before you get in.
How long
No government source sets a time limit. Two bath makers do: MTI about 10 minutes, Aquatic about 30. Hot tub makers say to lower the temperature once a soak goes past 10 minutes. Get out if you feel dizzy.
Hair
Keep long hair tied up and away from the suction fitting. Jacuzzi says at least 6 inches. CPSC has records of people held under water by hair caught in a suction fitting.
Alcohol
The CDC says not to drink before or during a hot tub soak. Manufacturers warn that alcohol, drugs or medication raise the risk of overheating and drowning.
Health and medication
If you take medication or have heart disease, high or low blood pressure or diabetes, the tub makers say to talk to a doctor first. For pregnancy the CDC says the same, and some manuals add a limit of 100°F.
Children
Makers say children should use a jetted tub only with an adult watching at all times, and MTI adds cooler water for young children. The CDC says children under 5 should not use hot tubs.
Electrics
Kohler asks for hair dryers, lamps, phones and radios to stay at least 5 feet from the tub. That matters most when the tub sits in the bedroom.
Getting in and out
Wet surfaces are slippery. The manuals say to get in and out slowly.

When something goes wrong

The jets will not start
Often the water is too low for the sensor. Add water until it is 2 inches above the highest jet. If nothing happens, the safety outlet may have tripped. Call the front desk: the manuals leave electrical faults to staff or an electrician.
The jets stopped on their own
The timer ran out, usually after 20 minutes. Press the button again.
Some jets are weak
Those jets may be closed. Twist the jet face until the flow comes back.
The tub is full of foam
Turn the jets off, drain the tub and refill it with fresh water. That is Duravit's fix.
The pump is loud
Low water lets the pump draw air. Kohler says the suction cover needs to be fully under water.
The air jets started by themselves after the bath
That is the drying cycle. Air tubs blow out their lines for a minute or two, often about 20 minutes after use.
The lights or panel do not respond
Call the front desk. The makers send electrical faults to a technician.

Using a private hot tub on a balcony or at a cabin

A hot tub on a private balcony, terrace or cabin deck usually stays filled and heated between uses, though some hosts drain and refill it between stays. That makes it a different job from a bath you fill yourself: the water may have been there before you, so it is worth a minute of checking.

Illustration: a private hot tub on a cabin deck at dusk with its cover folded back
A private hot tub at a cabin: cover fully off before you get in. Illustration.
  1. Take the whole cover off

    Lift it by the handles, never the straps, and fold it fully back or onto the lifter. Do not sit, stand or put things on it. One rental we read charges a fee for a damaged cover.

  2. Check the temperature

    The panel should read 104°F or less. Hot tubs usually run at 100°F to 104°F. If the tub was just filled, heating takes hours, so set the temperature and keep the cover on.

  3. Check the water

    The CDC suggests a test strip before you get in; how to use one is below. The CDC also says a properly chlorinated tub has little smell, and that a strong chemical smell means a problem. If the water looks or smells wrong, stay out and tell the host or front desk.

  4. Shower first

    The CDC recommends it: a one-minute shower removes most of the dirt, sweat and oils on your body.

  5. Use the panel

    On most tubs one press of the jets button gives low speed, a second press high, a third turns them off. Jets switch off after 15 to 20 minutes on many tubs, longer on some.

  6. Close it up

    Put the cover back on and lock the straps when you get out. The makers ask for it to keep children and pets out and the heat in.

Illustration: a hand holding a water test strip over a hot tub
Test strips show the disinfectant level and pH in under a minute. Illustration.

How to test the water with a strip

A test strip is a small stick with colored pads. Each pad holds a chemical that changes color with the level of one thing in the water, such as chlorine, bromine or pH. You match each pad to the color chart on the bottle. The chemical is used up in one dip, so a strip works only once. The CDC suggests buying them at a local retailer or pool supply store, so bring a bottle if your stay has a hot tub.

  1. Take a strip out with dry hands. Water on your fingers changes the reading.
  2. Dip it to about elbow depth, away from the jets, and take it straight out.
  3. Hold it level for 15 seconds, or the time on the bottle. Do not wipe or dry it.
  4. Match each pad to the color chart on the bottle, in daylight if you can.
  5. Throw the strip away after one use, and do not use strips past the date on the bottle.

The CDC gives these levels for hot tub users: free chlorine at least 3 ppm, or bromine 4 to 8 ppm, and pH 7.0 to 7.8. Above 10 ppm of chlorine or 8 ppm of bromine, it says to talk to the owner. If a reading is outside these ranges, stay out and tell the host or front desk. Hot tub maker Master Spas also says not to get in when the chlorine level is off.

No glass, soap or oils
One cabin rental's house rules we read ban breakable objects, soaps, bath oils and bubbles. Hot Spring advises against glass around the tub.
Storms
Get out when you hear thunder. Hot Spring says never to use an outdoor hot tub in a thunderstorm, and the National Weather Service says to get away from water.
Children
The CDC says no hot tubs for children under 5. Some rentals set a higher age; one we read says 14.
Germs
A poorly kept hot tub can spread hot tub rash and Legionella. The CDC notes that private hot tubs at vacation rentals are not held to the rules for public ones, so checking the water matters more there.

Two-person and heart-shaped tubs

Shape does not change how a tub works. A heart-shaped or two-person tub follows the same rules as any other tub of its type: fill above the jets, keep the water at 104°F or below, jets off before you get out. With two people the water rises more, so leave more room when you fill it. The heart-shaped tub itself goes back to 1963, when one of the founders of Cove Haven Resort in the Poconos invented it.

On our lists, 232 hotels and rentals describe the tub as built for two, and 80% of them have it in the bedroom, against 59% overall. Heart-shaped tubs are in the bedroom even more often: 47 of the 53, or 89%.

Looking for one? See our hotels with a heart-shaped jacuzzi, or the study of where hotels put the tub: by the bed or in the bathroom.

Frequently Asked Questions

How full should I fill a jetted tub?

At least 2 inches above the highest jet before you turn the jets on. Manufacturers ask for 1 to 2 inches, and American Standard suggests not filling past about two thirds before you get in.

Is the jacuzzi in the bedroom or the bathroom?

More often in the bedroom. Of the 5,900 hotels and rentals on TubHotels where a source confirms where the tub is, 59% have it in the bedroom, 38% in the bathroom and 2% on a private balcony or patio.

Can I use bubble bath in a hotel jacuzzi?

Not while the jets run. The jets turn even a small amount into heavy foam, and Kohler and Villeroy & Boch say to avoid it. If the tub foams over, turn the jets off, drain and refill.

Why did the jets stop by themselves?

Most jetted tubs have a timer that switches the jets off after about 20 minutes. Press the button again to restart them.

Do I need to clean the jacuzzi after using it?

No. Drain the tub when you are done. Flushing the pipes is the hotel's job, and none of the manuals we read asks guests to do it.

How do I test the water in a hot tub?

With a test strip. Use dry hands, dip it to elbow depth away from the jets, hold it level for 15 seconds and match the pads to the chart on the bottle. The CDC says free chlorine should be at least 3 ppm, or bromine 4 to 8 ppm, and pH 7.0 to 7.8.

Is it safe to use a hotel jacuzzi when pregnant?

The CDC says to talk to a healthcare provider before using a hot tub when pregnant. Some tub makers add a 100°F limit. Ask your doctor before you book a room for the tub.

What temperature should the water be?

No higher than 104°F (40°C), the limit from the CDC, CPSC and tub makers. Use cooler water for longer soaks and for children.

Sources

Every instruction on this page comes from these pages and manuals, opened in October 2026. Where they disagree, we say so above. Tubs differ, so a sign or card in your room comes first.